Flash Stock Firmware on Huawei Y6 SCL-U31 MT6582

Flash Stock Firmware on Huawei Y6 SCL-U31 MT6582

Flash Stock Firmware on Huawei Y6 SCL-U31 MT6582



Flash Stock Firmware on Huawei Y6 SCL-U31 MT6582

Flash Stock Firmware on Huawei Y6 SCL-U31 MT6582 I’m going to pass you the user guide for flashing stock firmware on Huawei Y6 SCL-U31 MT6582. In this guide we have used Dload folder method to flash the Stock Firmware on Huawei  And we include Official link to Download Huawei Y6 SCL-U31 MT6582 Stock rom and all Needed Files.  your device may get bricked And flashing stock ROM is the only way to go out.To perform this advance process of Flashing stock ROM please Go Step by step. If you got any error then leave a Comment.



Why I want to Flash Stock Firmware

If you have an Android device,you may require flashing Stock ROM/Firmware under various circumstances. If you have flashed custom ROM , Custom recovery or Custom kernel and facing several issues or if you want to Full Unroot, Unbrick,Rollback ,then  you have to flash stock ROM to bring your Huawei Y6 SCL-U31 MT6582 back to it’s original state.  Read More – Stock Rom vs Custom Rom



If you need to upgrade your Huawei then you have to find upgraded Stock/Custom Rom – kitkat, Marshmallow, Nougat.  we provide only Official Rom because all the glitches and bugs are debugged and you can get  latest OTA update and install them




Pre-requisites:



  1. It is always better to have the data back-up when we are dealing with the firmware and flashing things.
  2. Read More – Increase RAM SIZE after root on Huawei?
  3. Charge up your phone to at least 50-60 %, since the flashing takes some time and to be on the safer side.
  4. You must have Hisilicon Kirin chipset Read More – Check whether my one is Hisilicon Kirin or any else

Now if you are met with the pre-requisites, then start following the below mentioned steps one by one sequentially.



 






DISCLAIMER

Proceed at your own risk. flashstockrom.com will not be responsible for any mistake and any damage that might occur to your device while performing the following operation. Don’t skip any step.


Preparation – Flash Stock Firmware on Huawei Y6 SCL-U31 MT6582

Step 1: 

Create a new folder on your SD card and name the folder as dload.

Flash Stock Firmware on Huawei

Step 2:

Download Stock rom for Huawei Y6 SCL-U31 MT6582

Download the Huawei Stock Firmware to your computer beacase you have to unzip it. if you can unzip using huawei device then Download it to device directly . Read More – Enable OTG support on Huawei Device

Flash Stock Firmware on Huawei

Step 3:

No Update.app ? then Extract the downloaded file and find for update.app

Flash Stock Firmware on Huawei

Step 4:

Take a copy of the browsed file update.app and paste the same copy to the newly created folder on your SD card.

Step 5:

Now power off the Huawei device.

Turn off the Device

 

Start Flashing Stock Rom on Huawei Y6 SCL-U31 MT6582

Step 6:

Now hold the power+ Volume up+ Volume down buttons simultaneously for about 8-10 seconds until the flashing process starts automatically.  Read More – Increase Internal Rom SIZE After Root on Huawei.

Flash Stock Firmware on Huawei

Step 7: 

Wait patiently till the flashing completes. It may vary from 5-15 minutes depending on the requirement. Do not press any button until it completes.

 

Step 8:

The device reboots once the update process is done, wait for the device to restart and it should work properly.

Flash Stock Firmware on Huawei

Old One ? then

Flash Stock rom on Huawei

Congratulations! You must have flashed your Huawei Huawei Y6 SCL-U31 MT6582 successfully by now. This is one of the steps of flashing by turning the device off. We can also do the flashing without switching the device off. But, I always recommend the above mentioned steps, as it is the ideal one. Now, I will tell you the flashing steps without switching the device off.

Flash Stock Rom on Huawei Y6 SCL-U31 MT6582 without Turn Off

Step 1

Download Huawei Y6 SCL-U31 MT6582 and Follow the same procedures from Step 3,4.

step 2,

open Settings-> your Huawei smartphone ->About phone -> System update -> Local update.

Flash Stock Firmware on Huawei

Step 3,

Now tap the Update Option



Frequently Asked Questions Listed Below

 

I can’t Flash Stock Rom on Huawei Y6 SCL-U31 MT6582 .

Do it again with fresh Files. Your problem is persist then Leave a Comment With Full details about error. Then our team will help you. Or try this Tool

 Huawei  doesn’t turn on, or respond to power button ( Dead/Soft Brick).

  • After that Give up to 15mins for first boot.
  • Finally Find Rom from alternative source.
  • Read More

Huawei Doesn’t not pass boot logo/bootloop

After Flashing,  Huawei phone doesn’t pass the boot logo that mean,there is something wrong with your Huawei Y6 SCL-U31 MT6582 . However let it to start 15mins at least because this is first boot.After that if any Problem persists then Try to hard reset and do the Flash again. Or try this Tool

Huawei Y6 SCL-U31 MT6582  stuck at boot/ continuously restarts/ keep rebooting

first time it may give this kind of things. wait and watch. first boot may be slow. if Problem persists then Try to hard reset and do the Flashing Stock firmware on Huawei Y6 SCL-U31 MT6582  again with fresh Files. 

USB device not recognized

This is not related to Sp Flash tool. seems like this is error of your USB port for the reason that you get this error.Then you can fix it from here

Huawei Device auto restarting

  • It may be your  Huawei case is pressing on it (Clean the power button.)
  • or May be, your current stock Rom is damaged or Corrupted. So you have to Install Stock Rom/custom Rom to your device. use this post to Flash new Stock Rom.

Huawei cust fail Huawei Y6 SCL-U31 MT6582

try to reset if you can’t then I think that you should find another Stock firmware and try from it However let it to start 15mins at least because this is first boot.After that if any Problem persists then Try to hard reset and do the Flash again. Or try this Tool

dload:update partition MBR failed

try to reset if you can’t then I think that you should find another Stock firmware and try from it However let it to start 15mins at least because this is first boot.After that if any Problem persists then Try to hard reset and do the Flash again. Or try this Tool

“writing ‘recovery’… FAILED (remote: size too large)” 

getting this error message because your flashing twrp on Oreo. Nougat and Oreo kernels have different partition structure than the previous versions of Android



Thank you for coming to our Page. If this page helped you , So then please share this website to all Social Medias like Facebook ,twitter and Reddit so then Others can find this Huawei Guide. Finally If you have any problem then don’t hesitate, feel free to Leave a Comment with Error Message.So one of team our team member will help you as soon as possible.

vindya

leave a comment

Create Account



Log In Your Account



error: Content is protected !!

Copyright © 2015 - 2018 |Ramisunet Team | Romal All rights reserved